Design and analysis of a truss deployable antenna mechanism based on a 3UU-3URU unit

Space deployable structures with large calibers, high accuracy, and large folding ratios are indispensable equipment in the aerospace field. Given that the single-DOF 3RR-3RRR deployable unit cannot be fully folded, this study proposes a 3UU-3URU deployable unit with two kinds of DOF: folding movement and orientation adjustment. First, based on the G-K formula, the DOF of the 3UU-3URU unit is analyzed. Then, the 3UU-3URU unit is used to construct a deployable truss antenna with a curved surface, and the DOF of the whole deployable antenna containing multiple 3UU-3URU units is calculated. The structural design of a deployable antenna with two loops is carried out with specific parameters and geometric relations. Next, a DOF simulation of a basic combination unit composed of three 3UU-3URU units is performed. Finally, a prototype of the basic combination unit is manufactured, and the DOF of the mechanism is experimentally verified.     

某飞行器推力矢量试验测力装置研制

为满足某飞行器推力矢量试验的测试要求,采用两台六分量应变天平和一个空气桥组成测力装置来实现飞机全机气动力和喷管推进特性同时分别测量。基于有限元软件,对天平的应变及空气桥对天平的干扰进行了分析。结果表明:空气桥对天平力分量的干扰值优于5%,对力矩(滚转力矩除外)分量的干扰值优于15%,达到了设计指标。通过校准获得了单独天平、天平带空气桥(充压、不充压)状态下的校准公式,校准结果表明:两台天平各分量的综合加载误差均优于0.3%,天平带空气桥(充压、不充压)状态下各分量的综合加载误差优于0.5%,空气桥对天平的干扰量值与有限元分析结果一致。理论分析与实测结果证明:研制的天平及空气桥达到了预定目标,它的测量精准度高,满足推力矢量风洞试验需求。     

天基强银河背景下的空间碎片探测试验及分析

本文设计并完成了银河背景下碎片探测试验，数据分析表明，强的银河背景会降低探测器对暗弱碎片的探测能力，但对碎片的天文定位精度影响不大。本文验证了采用基于探测概率的极限探测星等方法表征探测器极限探测能力的合理性，以及基于仿真的方法增加数据完备度的可行性。本文的工作将为后续天基探测器的设计及探测试验的开展提供依据。     

Numerical investigation of flow mechanisms of tandem impeller inside a centrifugal compressor

This study numerically investigated a single stage centrifugal compressor ‘‘Radiver’’ with a wedge diffuser and several tandem-designed impellers to explore the flow phenomena within the tandem impeller and the potential to enhance compressor performance. The results demonstrate that tandem design and clocking fraction (λ_s) significantly affects the compressor performance. The compressor stage with tandem impellers of Series A of boundary layer growth interruption alone are observed to have a widely operating range but efficiency and total pressure ratio penalty compared with that of conventional impeller. The tandem impeller with at least the same impeller efficiency as the conventional design is considered as a critical design criteria so that further modification process based on the flow characteristic of tandem impeller is necessary. In order to restrain the inducer wake and exducer shock losses, parameters modification of blade angle and thickness distributions are necessary and the modified tandem impeller of Series B is obtained. The modified tandem impeller with 25% clocking arrangement shows an 8.45% stall margin increase and maintains the total pressure ratio and efficiency as the conventional design, which proves the potential of tandem impeller to improve compressor stage performance. It is noteworthy that the tandem impellers of Radiver have not shown obviously balanced exit flow field and the fundamental mechanism of stall margin extending of tandem impeller lies on the improved impeller/diffuser matching performance resulting from the incidence angle variation at diffuser inlet.     

基于不确定性的飞行器分离可靠性建模与分析方法

为实现飞行器分离任务可靠性的定量分析和高效精确评估，研究了高超声速飞行器分离任务过程中各种不确定性因素对分离可靠性的影响，提出一种基于不确定性的飞行器分离可靠性建模与分析方法。面向高超声速飞行器分离任务需求，建立分离动力学仿真模型，综合考虑分离过程不确定性因素的影响，利用灵敏度分析方法识别主要不确定性因素，构建分离可靠性模型。针对此模型，提出一种改进主动学习Kriging(IAK)的分离可靠性分析方法，通过新的采样策略选取失效概率更大的采样点作为新增训练点，进行高效可靠性分析。实例结果表明，该方法能够准确描述不确定性因素对分离过程的影响，提升分离可靠性定量分析的精度和效率，为飞行器分离方案的精细化设计提供支撑。     

Д-30发动机ЭИ868合金扇形块的钎焊修复

针对某Д-30发动机大修对ЭИ868合金(对应于我国的牌号GH3044)扇形块的修复要求,采用真空钎焊的方法对扇形块进行了钎焊补焊。对钎焊补焊的扇形块进行超声波探伤。结果表明,钎缝内部质量满足HB7575-97一级钎焊接头的要求,表明所确定的修复工艺可实现ЭИ868合金扇形块的可靠修复。     

航天产品非金属材料/ 制品贮存寿命评估技术

从非金属材料老化机理与寿命预测模型、老化行为表征技术、贮存环境试验与寿命评估技术等方面,概述了国内外的技术发展和现状,介绍了航天产品用非金属材料及制品贮存寿命评估技术的发展及其应用进展。     

基于结构健康监测的飞机结构 MSG-3 分析

结构健康监测(SHM)技术被广泛引入到了飞机设计与维护,本文依据现阶段SHM技术的发展现状,将SHM技术与MSG-3分析思想融合,制定了一种针对采用SHM技术飞机结构的计划维修分析流程。     

M40/4211 复合材料层合板铣削加工试验

通过分析碳纤维复合材料的性能特点及对切削加工性能的影响,提出了铣削刀具材料和几何结构形式的选用原则,介绍了几种适于碳纤维复合材料铣削的加工刀具。针对碳纤维复合材料中常用的M40/4211复合材料层合板进行加工缺陷试验和切削试验,总结出影响M40/4211复合材料层合板加工质量的因素及规律,得到每种刀具加工M40/4211复合材料层合板的最佳加工参数,较高的切削速度配合恰当的进给速度可以有效提高M40/4211复合材料层合板的加工质量和加工效率。